How to Remove and Replace a Kitchen Sink Faucet

The most difficult part of replacing a kitchen faucet is to remove the old faucet. Unexpected problems always arise like corroded pipes, hard-to-reach nuts, and fittings. Otherwise, to remove and replace a kitchen sink faucet is not difficult at all. In fact, the instructions that come with the new faucet may be all you need to complete this part of the job.

In this article, you will complete a basic replacement process and tell you how to deal with those tricky parts.

Materials You Need

  1. Plumber’s Grease
  2. Replacement Cartridge

Equipment You Need

  1. Multi-head screwdriver
  2. Basin cock wrench
  3. Slip joint pliers

Step-by-Step Instructions to Remove and Replace a Kitchen Sink Faucet:

1. Turn Off the Water and Disconnect Supply Lines

remove and replace kitchen sink faucets

Before removing the kitchen faucet, you must first properly disconnect the water supply line. The water supply line is located under the sink, just below the tap. Whether it is a single-handle kitchen faucet or a double-handle kitchen faucet, there are two lines. One is used for hot water and the other is used for cold water.

Before starting, block the sink drain with a cloth. You can also place a bucket under the sink to catch dripping water. Use an adjustable wrench to loosen the nut connecting the supply line to the sink. Continue to turn the nut until both water supply lines are available.

2. Remove the Faucet

remove the faucets

Gently pull the entire faucet upward. If it sticks, use the edge of a plastic putty knife to carefully loosen it. After removal, use a putty knife to remove any old plumber’s putty or caulk from the surface of the sink. Be careful not to scratch the sink. Before removing the faucet, you may need to take it apart first. For example, if you want to remove a single-handle faucet, unscrew the handle from the main valve. Be sure to check the faucet manufacturer’s manual for specific disassembly instructions.

3. Replace the Faucet

replace the faucets

Remove the soap container and lock the nut from the soap dispenser. Apply the plumber’s putty to the bottom edge and insert it into the hole farthest from the centre. Apply a large amount of plumber’s putty to the bottom of the hole cover, and then place it firmly on the three centre holes of the sink. Pass the faucet through the hole in the cover, and then place the faucet with the handle facing the correct direction.

4. Connect Supply Lines & Turn On the Water

Screw the plastic lock nut onto the handle of the soap dispenser, and then use a basin wrench to tighten it. Screw the soap container onto the handle, making sure it is tight. Slide the heavy object onto the spray hose and connect both ends to make sure they lock in place. Position the hot and cold supply lines so that they do not interfere with other hoses, then connect them to the existing supply lines and tighten them.

5. Finish the Installation

Open the hot and cold supply lines, and then turn on the water tap. Remove excess putty around the shield. Add soap to the dispenser and fix the pump on the top.

Manual: Remove and Replace a Kitchen Sink Faucets (PDF)

Some Tips on Removing the Faucet

Some faucets that have been used for a long time seem to be unable to be removed. Corrosion or mineral deposits can freeze nuts or bolts. You can take a variety of measures to correct this situation. First, soak the jammed nuts, valve handles and screws with penetrating oil. The longer you let it soak, the better. If using penetrating oil does not work, there are several other solutions you can try:

  • If jammed nuts or bolts are covered by mineral deposits, use white vinegar and a wire brush to remove them.
  • Tap the nut lightly with a hammer to turn it.
  • Heat the nut or screw directly. The heat can expand the metal enough to turn it.

Video Instructions

Video Source: YouTube


Can I replace a kitchen faucet myself?

The new kitchen faucet is a simple and affordable way to update. Using some basic tools, you can easily install or replace the kitchen faucet.

How much does it cost to remove and replace a kitchen faucet?

The kitchen faucets cost $100-$150 on average. There is no need to pay for labour cost because you can easily remove and replace a kitchen faucet yourself by following the instructions that I described above.

How do I remove a single handle kitchen faucet?

To remove a single handle kitchen faucet, you can follow the above instructions. Following these instructions, you can remove and replace a kitchen faucet of both single handle or double handle.

Final Thoughts

You won’t believe how easy it is to remove and replace a kitchen sink faucet! If I can do it, so can you! Come on, do it yourself! If you have any questions or suggestions, please contact me or leave a comment!

In short, if you want to remove and replace a kitchen sink faucet, be sure to check out the best kitchen faucets.

3 thoughts on “How to Remove and Replace a Kitchen Sink Faucet”

  1. Pingback: How to Disassemble a Moen Kitchen Faucet? Step-by-Step Instructions - Faucet Goods

  2. Pingback: How to Disconnect Sprayer Hose From Delta Faucet? Step-by-Step Instructions - Faucet Goods

  3. Pingback: How to Remove Bathroom Sink Faucet Handle That Has No Screw? 3 Different Ways - Faucet Goods

Leave a Comment

Your email address will not be published. Required fields are marked *