How to Disassemble a Moen Kitchen Faucet? Step-by-Step Instructions

Learning how to disassemble a Moen kitchen faucet can be a bit challenging at first. Before starting the project, you should understand the model and type of Moen kitchen faucet to be removed in order to obtain the correct replacement parts for the malfunctioning faucet. The removal and installation of almost all Moen kitchen faucets are similar and relatively easy. If you want to remove one or even install a new part in its place, there is no need to hire a plumber.

However, even if you have never done it before, the job is very simple and intuitive. Although there are some methods that can go wrong, this tutorial will teach you how to do it right away.

Materials You Need

  1. Grease
  2. A New Moen Kitchen Faucet

Equipment You Need

  1. Wrench
  2. Needle nose pliers
  3. Screwdriver

Step-by-Step Instructions to Disassemble a Moen Kitchen Sink Faucet:

1. Turn Off the Water Lines

shut off the water supply - how to remove a moen kitchen faucet

This is your first step in this process. Just place the main valve close to the water meter. Ideally, you should install some shut-off valves before installing a new faucet. Make sure you are in the position where the water pipe is connected to the water supply pipe. Unless you want a disaster in the kitchen, you must shut them down before starting operations.

2. Dry the Pipe

Before you start repairing the Moen kitchen faucet, you need to make sure that the pipe is empty. Turn on the Moen faucet to drain the water that may still be in the pipe. Before starting to disassemble the Moen faucet, the water pipes around the Moen faucet must be emptied.

3. Remove the Handle

remove the handle - how to remove a moen kitchen faucet

Disconnect the hot and cold water supply pipes. You should do it one at a time. If they get stuck a little bit, you will notice that the shut-off valve will also move. You can use a set of pliers or wrenches to hold each shut-off valve in place. If they are not in optimal condition, you can also replace them before installing a new faucet.

4. Remove the Nuts

After removing the handle, you will see nuts. The faucet is installed and fixed with some nuts. Learn how to disassemble the Moen kitchen faucet from these nuts. They enter the tailgate but are also located under the sink. Turn the nut counterclockwise. If this job seems impossible, or if you feel you want to destroy them, just spray some penetrating oil.

5. Take Out the Handle Mechanism

remove the handle mechanism - how to remove a moen kitchen faucet

After removing the nut, you can take out the handle mechanism. The handle mechanism controls the flow of the waterline, so please be careful not to damage it. You will notice a screw securing the device to the sink. Use a screwdriver to loosen the screw, and then remove the mechanism.

6. Remove the Nozzle and Pull Out the Cartridge

Remove the Nozzle and Pull Out the Cartridge - how to remove a moen kitchen faucet

After removing all the rings and washers blocking the way, you will see the nozzle. Without any tools, the nozzle will slip off. After removing the nozzle, you will see a clip holding the ink cartridge. The clamp can be removed with a screwdriver.

If you have an old faucet, you must also disassemble the faucet. Clamp the valve stem with pliers and rotate the faucet until it loosens. If the pliers do not work, you may have to use a cartridge puller.

Video Instructions:

This is the video tutorial in which you get to know how to disassemble a Moen kitchen faucet on your own without a plumber. Please watch the full video for a better understanding.

Source: YouTube

Manual: How to Disassemble a Moen Kitchen Faucet (PDF)

FAQs

How Do You Remove a Stuck Faucet Nut?

If it does not rotate, you should hit the fixture hard with a hard rubber hammer. If you don’t have a hard rubber hammer, place a centre punch on your fixture and hit it with a hammer. To loosen the faucet, you should place the wrench on the nut and hit it with a hammer.

Why Is My Moen Kitchen Faucet Leaking?

There are usually many reasons for leaks in Moen faucets. Since the pull-out sprinkler has only one handle, the most common cause of water leakage is the O-ring. To replace the O-ring, turn off the water supply to the faucet from under the faucet.

How do you loosen a Moen faucet handle?

The lever handle is screwed into the handle hub by hand, and the handle hub is screwed to the faucet assembly by hand. To remove the hub, simply twist the hub counterclockwise until it can be removed from the faucet assembly.

Final Thoughts

Most people choose to replace their faucet because the process is fast and they will actually save some money. In fact, if you install a new faucet, sometimes the cost of plumbing service will be higher than the actual faucet. It may seem difficult at first, but once you learn how to disassemble a moen kitchen faucet yourself, it will be worth it. For other faucets, you can read this article.

Leave a Comment

Your email address will not be published. Required fields are marked *